Wiser 2 issues after project update

Hi today I made a few changes to my wiser 2 project file (added 2 schedules) and downloaded, now it seems to have a few issues.

It wont seem to boot correctly.

After the project update and reboot the only lights that are on at the front of the unit are the power light (solid Green) and the MRA light (solid Yellow).

The only way i have been able to get it it boot is to remove the power hold the reset button in on the bottom of the unit and apply power again until all the lights flash red then remove and reconnect power again.

But now the wiser UI is extremely slow, when a menu button is pressed it takes a good second or 2 to change pages or locations.

I have also tried to re downloaded the firmware as well, the current version is 1_31_463 but when the unit rebooted it got stuck again.

Is my unit on the way out already ? Or is this another issue?

Should I try to reset it back to factory defaults?

 

This is the Diag output if it helps at all.

Code:

Diagnostics Output

eth0      Link encap:Ethernet  HWaddr 00:17:DD:04:13:56  
          inet addr:192.168.0.2  Bcast:192.168.0.255  Mask:255.255.255.0
          inet6 addr: fe80::217:ddff:fe04:1356/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:6737 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7598 errors:1 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:487722 (476.2 KiB)  TX bytes:6342757 (6.0 MiB)
          Interrupt:182 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNI?4
d input'.
I/EventHub( 1395): New device: id=2, fd=156, path='/dev/input/event1', name='HDMI CEC Keyboard input', classes=0x1, configuration='', keyLayout='/system/usr/keylayout/Generic.kl', keyCharacterMap='/system/usr/keychars/Generic.kcm', builtinKeyboard=false
I/InputReader( 1395): Device added: id=2, name='HDMI CEC Keyboard input', sources=0x00000101
E/WifiStateMachine( 1395): Unable to change interface settings: java.lang.IllegalStateException: Unable to communicate with native daemon to set ipv6privacyextensions - com.android.server.NativeDaemonConnectorException: Cmd {interface ipv6privacyextensions wlan0 enable} failed with code 400 : {Failed to set ipv6 privacy extensions (No such file or directory)}
I/BackupManagerService( 1395): New app android never backed up; scheduling
I/BackupManagerService( 1395): New app com.android.browser never backed up; scheduling
I/BackupManagerService( 1395): New app com.android.inputmethod.latin never backed up; scheduling
I/wpa_supplicant( 1524): rfkill: Cannot open RFKILL control device
I/BackupManagerService( 1395): New app com.android.providers.settings never backed up; scheduling
I/BackupManagerService( 1395): New app com.android.providers.userdictionary never backed up; scheduling
I/BackupManagerService( 1395): New app com.android.sharedstoragebackup never backed up; scheduling
V/BackupManagerService( 1395): Registering transport android/com.android.internal.backup.LocalTransport = com.android.internal.backup.LocalTransport@411e1998
V/BackupManagerService( 1395): Starting with transport android/com.android.internal.backup.LocalTransport
V/BackupManagerService( 1395): Google transport not present
I/BackupManagerService( 1395): Found stale backup journal, scheduling
I/BackupManagerService( 1395):   android
I/BackupManagerService( 1395):   com.android.browser
I/BackupManagerService( 1395):   com.android.inputmethod.latin
I/BackupManagerService( 1395):   com.android.providers.settings
I/BackupManagerService( 1395):   com.android.providers.userdictionary
I/BackupManagerService( 1395):   com.android.sharedstoragebackup
I/BackupManagerService( 1395): Backup enabled => false
I/BackupManagerService( 1395): Opting out of backup
I/SystemServer( 1395): AppWidget Service
I/SystemServer( 1395): Recognition Service
I/SystemServer( 1395): DiskStats Service
W/Vibrator( 1395): Failed to vibrate; no vibrator service.
I/WindowManager( 1395): SAFE MODE not enabled
D/dalvikvm( 1395): JIT started for system_server
I/SystemServer( 1395): SamplingProfiler Service
D/PowerManagerService( 1395): system ready!
I/ActivityManager( 1395): System now ready
I/SystemServer( 1395): Making services ready
D/SystemServer( 1395): Starting service: Intent { cmp=com.android.systemui/.SystemUIService }
W/ActivityManager( 1395): Unable to start service Intent { cmp=com.android.systemui/.SystemUIService }: not found
D/NetworkManagementService( 1395): not enabling bandwidth control
W/NetworkStats( 1395): problem reading network stats: java.lang.IllegalStateException: problem parsing idx 1
D/NetworkManagementService( 1395): Registering observer
D/NetworkManagementService( 1395): Registering observer
I/ActivityManager( 1395): Config changed: {1.0 0mcc0mnc en_US layoutdir=0 sw720dp w1280dp h672dp lrg long land -touch -keyb/v/h -nav/h s.3}
W/RecognitionManagerService( 1395): no available voice recognition services found
W/InputManagerService( 1395): Ignoring setImeWindowStatus of uid 1000 token: null
I/Zygote  ( 1395): Process: zygote socket opened
D/dalvikvm( 1395): GC_CONCURRENT freed 302K, 5% free 7791K/8199K, paused 5ms+16ms
I/ActivityManager( 1395): Start proc com.android.inputmethod.latin for service com.android.inputmethod.latin/.LatinIME: pid=1528 uid=10004 gids={}
D/NetworkManagementService( 1395): Registering observer
I/ActivityManager( 1395): START {act=android.intent.action.MAIN cat=[android.intent.category.HOME] flg=0x10000000 cmp=com.wiser2.launcher/.LoginScreen} from pid 0
I/ActivityManager( 1395): Start proc com.wiser2.launcher for activity com.wiser2.launcher/.LoginScreen: pid=1546 uid=10019 gids={3002, 3003}
I/SystemServer( 1395): Enabled StrictMode for system server main thread.
W/NetworkManagementSocketTagger( 1395): setKernelCountSet(10019, 1) failed with errno -2
W/ThrottleService( 1395): unable to find stats for iface rmnet0
I/wpa_supplicant( 1524): wpa_driver_nl80211_driver_cmd: Unsupported command BTCOEXSCAN-STOP
I/ActivityManager( 1395): Start proc com.android.settings for broadcast com.android.settings/.widget.SettingsAppWidgetProvider: pid=1567 uid=1000 gids={1015, 3002, 3001, 3003}
I/wpa_supplicant( 1524): wpa_driver_nl80211_driver_cmd: Unsupported comma?4
 1675): ====> Connection Helper: process stopped
I/WiserCore( 1675): Wifi Service> update wifi config: started
I/WiserCore( 1675): Wifi Service> update wifi config - clearing wifi configurations...
I/WiserCore( 1675): Wifi Service> update wifi config - disabling wifi
D/CommandListener( 1154): Clearing all IP addresses on wlan0
I/System.out( 1675): ====> Connection Helper: attempt 1: connected to '127.0.0.1' on port '8888'
I/System.out( 1675): ====> Connection Helper: process stopped
I/System.out( 1675): ====>>> text reader started!.....
I/System.out( 1675): ====>>> text reader started!.....
I/System.out( 1675): ====>>> text reader started!.....
I/WiserCore( 1675): Projector Key Reader> reading projector key: begin
I/WiserCore( 1675): Projector Key Reader> reading projector key: begin
I/WiserCore( 1675): Projector Key Reader> reading projector key: begin
D/dalvikvm( 1259): GC_EXPLICIT freed 34K, 5% free 6475K/6787K, paused 4ms+86ms
D/ConnectivityService( 1395): ConnectivityChange for WIFI: DISCONNECTED/DISCONNECTED
D/ConnectivityService( 1395): tryFailover: - jaya - disabled failover and just do reconnect
D/ConnectivityService( 1395): tryFailover: - jaya - force reconnect for WIFI
D/ConnectivityService( 1395): ConnectivityChange for WIFI: DISCONNECTED/DISCONNECTED
D/ConnectivityService( 1395): tryFailover: - jaya - disabled failover and just do reconnect
D/ConnectivityService( 1395): tryFailover: - jaya - force reconnect for WIFI
I/wpa_supplicant( 1524): wlan0: CTRL-EVENT-TERMINATING 
F/NetworkStats( 1395): problem reading network stats
F/NetworkStats( 1395): java.lang.IllegalStateException: problem parsing idx 1
F/NetworkStats( 1395): 	at com.android.internal.net.NetworkStatsFactory.readNetworkStatsDetail(NetworkStatsFactory.java:300)
F/NetworkStats( 1395): 	at com.android.server.NetworkManagementService.getNetworkStatsUidDetail(NetworkManagementService.java:1282)
F/NetworkStats( 1395): 	at com.android.server.net.NetworkStatsService.performPollLocked(NetworkStatsService.java:831)
F/NetworkStats( 1395): 	at com.android.server.net.NetworkStatsService.updateIfacesLocked(NetworkStatsService.java:743)
F/NetworkStats( 1395): 	at com.android.server.net.NetworkStatsService.updateIfaces(NetworkStatsService.java:721)
F/NetworkStats( 1395): 	at com.android.server.net.NetworkStatsService.access$000(NetworkStatsService.java:128)
F/NetworkStats( 1395): 	at com.android.server.net.NetworkStatsService$1.onReceive(NetworkStatsService.java:612)
F/NetworkStats( 1395): 	at android.app.LoadedApk$ReceiverDispatcher$Args.run(LoadedApk.java:728)
F/NetworkStats( 1395): 	at android.os.Handler.handleCallback(Handler.java:605)
F/NetworkStats( 1395): 	at android.os.Handler.dispatchMessage(Handler.java:92)
F/NetworkStats( 1395): 	at android.os.Looper.loop(Looper.java:137)
F/NetworkStats( 1395): 	at android.os.HandlerThread.run(HandlerThread.java:60)
F/NetworkStats( 1395): Caused by: java.io.FileNotFoundException: /proc/net/xt_qtaguid/stats: open failed: ENOENT (No such file or directory)
F/NetworkStats( 1395): 	at libcore.io.IoBridge.open(IoBridge.java:406)
F/NetworkStats( 1395): 	at java.io.FileInputStream.(FileInputStream.java:78)
F/NetworkStats( 1395): 	at com.android.internal.net.NetworkStatsFactory.readNetworkStatsDetail(NetworkStatsFactory.java:269)
F/NetworkStats( 1395): 	... 11 more
F/NetworkStats( 1395): Caused by: libcore.io.ErrnoException: open failed: ENOENT (No such file or directory)
F/NetworkStats( 1395): 	at libcore.io.Posix.open(Native Method)
F/NetworkStats( 1395): 	at libcore.io.BlockGuardOs.open(BlockGuardOs.java:110)
F/NetworkStats( 1395): 	at libcore.io.IoBridge.open(IoBridge.java:390)
F/NetworkStats( 1395): 	... 13 more
D/dalvikvm( 1675): GC_CONCURRENT freed 399K, 7% free 7121K/7623K, paused 4ms+10ms
I/WiserCore( 1675): CBD Socket> on connected to '127.0.0.1' port '8888': projector key '0xBC63271'
I/WiserCore( 1675): CBD Socket> sending - auth command: ''
I/WiserCore( 1675): Wifi Service> update wifi config - enabling ethernet
I/WiserCore( 1675): Wifi Service> broadcast event: got wifi state change
I/WiserCore( 1675): Wifi Service> broadcast event: got wifi state change - else
I/WiserCore( 1675): Ripple Socket> on connected to '127.0.0.1' port '20030': projector key '0xBC63271'
I/WiserCore( 1675): Ripple Socket> sending - auth command: ''
I/WiserCore( 1675): Socket Service> : ripple daemon - socket connected
I/WiserCore( 1675): ZBD Socket> on connected to '127.0.0.1' port '8890': projector key '0xBC63271'
I/WiserCore( 1675): ZBD Socket> sending - auth command: ''
I/WiserCore( 1675): Socket Service> : zigbee daemon - socket connected
I/Wiser 2 App( 1626): MRA v3?4
 '1' - 'Row1' - 'bulb'
I/System.out( 1626): ===> new dimmer: 'General Lighting Dimmer' - 'loc:Living Room' - 'fg:Light' : '254' - '56' - '17' - ramprate: '1' - 'Row2' - 'bulb'
I/System.out( 1626): ===> new dimmer: 'General Lighting Dimmer' - 'loc:Living Room' - 'fg:Light' : '254' - '56' - '18' - ramprate: '1' - 'Row3' - 'bulb'
I/System.out( 1626): ===> new dimmer: 'General Lighting Dimmer' - 'loc:Living, Dining, Kitchen' - 'fg:Light' : '254' - '56' - '5' - ramprate: '1' - 'Kitchen Bench' - 'bulb'
I/System.out( 1626): ===> new dimmer: 'General Lighting Dimmer' - 'loc:Living, Dining, Kitchen' - 'fg:Light' : '254' - '56' - '15' - ramprate: '1' - 'Night Light' - 'bulb'
I/System.out( 1626): ===> new Fan Controller: 'Fan Controller' - 'loc:Living, Dining, Kitchen' - 'fg:Fan' : '254' - '56' - '61' - label 'Kitchen Fan' - speeds 'Slow|25|Medium|127|Fast|242|Off|0'
I/System.out( 1626): ===> new dimmer: 'General Lighting Dimmer' - 'loc:Living, Dining, Kitchen' - 'fg:Light' : '254' - '56' - '3' - ramprate: '1' - 'Dining Room Lights' - 'bulb'
I/System.out( 1626): ===> new Fan Controller: 'Fan Controller' - 'loc:Living, Dining, Kitchen' - 'fg:Fan' : '254' - '56' - '56' - label 'Dining Room Fan' - speeds 'Slow|25|Medium|127|Fast|242|Off|0'
I/System.out( 1626): ===> new dimmer: 'General Lighting Dimmer' - 'loc:Living, Dining, Kitchen' - 'fg:Light' : '254' - '56' - '16' - ramprate: '1' - 'Row1' - 'bulb'
I/System.out( 1626): ===> new dimmer: 'General Lighting Dimmer' - 'loc:Living, Dining, Kitchen' - 'fg:Light' : '254' - '56' - '17' - ramprate: '1' - 'Row2' - 'bulb'
I/System.out( 1626): ===> new dimmer: 'General Lighting Dimmer' - 'loc:Living, Dining, Kitchen' - 'fg:Light' : '254' - '56' - '18' - ramprate: '1' - 'Row3' - 'bulb'
I/System.out( 1626): ===> new Fan Controller: 'Fan Controller' - 'loc:Living, Dining, Kitchen' - 'fg:Fan' : '254' - '56' - '62' - label 'Living Room Fan' - speeds 'Slow|25|Medium|127|Fast|242|Off|0'
I/System.out( 1626): ===> new dimmer: 'General Lighting Dimmer' - 'loc:Living, Dining, Kitchen' - 'fg:Light' : '254' - '56' - '7' - ramprate: '1' - 'Hall Lights' - 'bulb'
I/System.out( 1626): ===> new dimmer: 'General Lighting Dimmer' - 'loc:Living, Dining, Kitchen' - 'fg:Light' : '254' - '56' - '141' - ramprate: '1' - 'Kitchen Bench Led Strip' - 'bulb'
I/System.out( 1626): ===> new power meter: 'Power Meter' - 'loc id:16' - 'fg id:-1' : meter no '0' power meter 'Phase 1' -  hourly_max_w: '0' - daily_max_w: '0'' - weekly_max_w: '0' - monthly_max_w: '0' - default_units: '0' - currency_units: '$' - min_threshold: '0' - max_threshold: '50'
I/System.out( 1626): ===> new power meter: 'Power Meter' - 'loc id:16' - 'fg id:-1' : meter no '1' power meter 'Phase 2' -  hourly_max_w: '0' - daily_max_w: '0'' - weekly_max_w: '0' - monthly_max_w: '0' - default_units: '0' - currency_units: '$' - min_threshold: '0' - max_threshold: '50'
I/System.out( 1626): ===> new power meter: 'Power Meter' - 'loc id:16' - 'fg id:-1' : meter no '2' power meter 'Solar' -  hourly_max_w: '0' - daily_max_w: '0'' - weekly_max_w: '0' - monthly_max_w: '0' - default_units: '0' - currency_units: '$' - min_threshold: '0' - max_threshold: '50'
I/System.out( 1626): ===> new total power meter: 'Power Meter Totals' - 'loc id:16' - 'fg id:-1' : meter no '-1' power meter 'Phase 1' - hg '0' hc '0' dg '0' dc '0' wg '0' wc '0' mg '0' mc '0'  - default_units: '0' - currency_units: '$'
I/System.out( 1626): ===> new power meter: 'Power Meter' - 'loc id:16' - 'fg id:-1' : meter no '3' power meter 'Tarriff 33' -  hourly_max_w: '0' - daily_max_w: '0'' - weekly_max_w: '0' - monthly_max_w: '0' - default_units: '0' - currency_units: '$' - min_threshold: '0' - max_threshold: '50'
I/System.out( 1626): ===> new Homesafe Panel: zones 'Garge Door|1|Front Door|2|Shop Door|3|Shop Door Back|4|Shop|5|Garage|6|Back Door|7|Laundry Door|8|Living Room|9|Matts Room|10|Amys Room|11' 'loc:Security' - 'fg:'
I/System.out( 1626): ===> new Bell Press: 'Bellpress' - 'loc:' - 'fg:AirCon' : '254' - '112' - '3' - 'Dakin 12000 On 23deg' - 'bellpress'
I/System.out( 1626): ===> new Bell Press: 'Bellpress' - 'loc:' - 'fg:AirCon' : '254' - '112' - '7' - 'Dakin 12000 Off' - 'albums'
I/System.out( 1626): ===> new Bell Press: 'Bellpress' - 'loc:' - 'fg:AirCon' : '254' - '112' - '12' - 'Dakin 24000 On 23deg' - 'albums'
I/System.out( 1626): ===> new Bel?4
icy: ECC disabled, Data cache writeback
OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk )
SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000
On node 0 totalpages: 62464
free_area_init_node: node 0, pgdat c073e18c, node_mem_map c080e000
  Normal zone: 512 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61952 pages, LIFO batch:15
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 61952
Kernel command line: console=ttyO2,115200n8 androidboot.console=ttyO2 mem=256M init=/init mpurate=600 vram=12M omapfb.vram=0:12M omapfb.mode=dvi:1280x720-24 omapdss.def_disp=dvi rootwait rw ubi.mtd=4 ip=off fdflt=1 rootfstype=ubifs root=ubi0:rootfs1
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 244MB = 244MB total
Memory: 239320k/239320k available, 22824k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
    vmalloc : 0xd0800000 - 0xf8000000   ( 632 MB)
    lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .init : 0xc0008000 - 0xc003d000   ( 212 kB)
      .text : 0xc003d000 - 0xc06f3000   (6872 kB)
      .data : 0xc06f4000 - 0xc0743640   ( 318 kB)
NR_IRQS:409
Clocking rate (Crystal/Core/MPU): 26.0/664/600 MHz
Reprogramming SDRC clock to 664000000 Hz
dpll3_m2_clk rate change failed: -22
IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
GPMC revision 5.0
Trying to install interrupt handler for IRQ402
Trying to install interrupt handler for IRQ403
Trying to install interrupt handler for IRQ404
Trying to install interrupt handler for IRQ405
Trying to install interrupt handler for IRQ406
Trying to install interrupt handler for IRQ407
Trying to install interrupt handler for IRQ408
Trying to install type control for IRQ409
Trying to set irq flags for IRQ409
OMAP clockevent source: GPTIMER1 at 32768 Hz
Console: colour dummy device 80x30
Calibrating delay loop... 597.64 BogoMIPS (lpj=2334720)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
devtmpfs: initialized
regulator: core version 0.5
regulator: dummy: 
NET: Registered protocol family 16
OMAP GPIO hardware version 2.5
OMAP GPIO hardware version 2.5
OMAP GPIO hardware version 2.5
OMAP GPIO hardware version 2.5
OMAP GPIO hardware version 2.5
OMAP GPIO hardware version 2.5
omap_mux_init: Add partition: #1: core, flags: 0
set i2c2 irq to 332
Wiser2: registering i2c3 bus for NXP HDMI
Wiser2: May 21 2014 20:39:31 registering wl12xx wifi platform device
wiser2: bt init
Found NAND on CS0
Registering NAND on CS0
wiser2_ethernet_init:960
wiser2_ethernet_init:962
GPIO21 eth RESET=1
GPIO22 eth irq=1
hw-breakpoint: debug architecture 0x4 unsupported.
Switched to new clocking rate (Crystal/Core/MPU): 26.0/664/600 MHz
OMAP DMA hardware revision 5.0
bio: create slab  at 0
machine_constraints_voltage: override 'vwl1271' min_uV, 1 -> 1800000
machine_constraints_voltage: override 'vwl1271' max_uV, 2147483647 -> 1800000
regulator: vwl1271: 1800 mV 
reg-fixed-voltage reg-fixed-voltage.1: vwl1271 supplying 1800000uV
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
omap_i2c omap_i2c.1: bus 1 rev4.0 at 2600 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
machine_constraints_voltage: override 'VUSB1V5' min_uV, 1 -> 1500000
machine_constraints_voltage: override 'VUSB1V5' max_uV, 2147483647 -> 1500000
regulator: VUSB1V5: 1500 mV normal standby
machine_constraints_voltage: override 'VUSB1V8' min_uV, 1 -> 1800000
machine_constraints_voltage: override 'VUSB1V8' max_uV, 2147483647 -> 1800000
regulator: VUSB1V8: 1800 mV normal standby
machine_constraints_voltage: override 'VUSB3V1' min_uV, 1 -> 3100000
machine_constraints_voltage: override 'VUSB3V1' max_uV, 2147483647 -> 3100000
regulator: VUSB3V1: 3100 mV normal standby
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
regula?4
463 - Thu Nov 20 12:16:10 MYT 2014
cat: can't open '/userversion.txt': No such file or directory
Module                  Size  Used by
hdmicec                56274  2 
omaplfb                10598  0 
pvrsrvkm              154317  23 omaplfb
hdmitx                115058  2 hdmicec
wl12xx                168746  0 
mac80211              327777  1 wl12xx
cfg80211              158053  2 mac80211,wl12xx
compat                  7131  2 mac80211,wl12xx
cat: can't open '/mnt/microsd/clipsal/gen/log.ddns': No such file or directory
PING google.com (216.58.196.142): 56 data bytes
64 bytes from 216.58.196.142: seq=0 ttl=53 time=55.847 ms

--- google.com ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max = 55.847/55.847/55.847 ms
nameserver 192.168.0.1
nameserver 192.168.0.3
serinfo:1.0 driver revision:
0: uart:OMAP UART0 mmio:0x4806A000 irq:72 tx:41482 rx:2939 DSR|CD|RI
1: uart:OMAP UART1 mmio:0x4806C000 irq:73 tx:10749 rx:276790 RTS|CTS|DTR|DSR|CD|RI
2: uart:OMAP UART2 mmio:0x49020000 irq:74 tx:17 rx:0 RTS|CTS|DTR|DSR|CD|RI
3: uart:OMAP UART3 mmio:0x49042000 irq:80 tx:0 rx:0 CTS|DSR|CD|RI
cat: can't open '/proc/tty/driver/ttySC': No such file or directory
serinfo:1.0 driver revision:
0: uart:NXP16IS7xx port:00000000 irq:332 tx:1491 rx:178 RTS|DTR
 14:28:08 up  1:04,  load average: 0.02, 0.02, 0.04
           CPU0
  7:          0        INTC  TWL4030-PIH
 11:          0        INTC  prcm
 12:       1863        INTC  DMA
 20:          0        INTC  gpmc
 21:      67987        INTC  SGX ISR
 24:          0        INTC  omap-iommu.0, OMAP3 ISP
 25:       8293        INTC  OMAP DSS
 37:    1826820        INTC  gp timer
 56:       1250        INTC  omap_i2c
 57:     253613        INTC  omap_i2c
 61:   11039823        INTC  omap_i2c
 72:       3169        INTC  serial idle
 73:      21048        INTC  serial idle, OMAP UART1
 74:          2        INTC  serial idle, OMAP UART2
 77:        133        INTC  ehci_hcd:usb1
 80:          0        INTC  serial idle
 83:       3583        INTC  mmc0
 86:          0        INTC  mmc1
 92:          0        INTC  musb-hdrc.0
 93:          0        INTC  musb-hdrc.0
 94:       1451        INTC  mmc2
182:       4939        GPIO  eth0
217:          1        GPIO  TDA IRQ
267:          0        GPIO  mmc1
332:       1472        GPIO  i2c serial
376:          0     twl4030  twl4030_pwrbutton
378:          0     twl4030  twl4030_usb
379:          0     twl4030  rtc0
384:          0     twl4030  mmc0
Err:          0
1688 loopend cbuslasterr=0, cbusconnected=1 transparent_mode=0 got_ntp=1
  sl  local_address rem_address   st tx_queue rx_queue tr tm->when retrnsmt   uid  timeout inode                                                     
   0: 0100007F:13AD 00000000:0000 0A 00000000:00000000 00:00000000 00000000     0        0 3093 1 ce7299c0 300 0 0 2 -1                              
   1: 00000000:2090 00000000:0000 0A 00000000:00000000 00:00000000 00000000     0        0 4153 1 ce728040 300 0 0 2 -1                              
   2: 00000000:2711 00000000:0000 0A 00000000:00000000 00:00000000 00000000     0        0 4156 1 ce7288c0 300 0 0 2 -1                              
   3: 00000000:2091 00000000:0000 0A 00000000:00000000 00:00000000 00000000     0        0 4154 1 ce728480 300 0 0 2 -1                              
   4: 00000000:22B8 00000000:0000 0A 00000000:00000000 00:00000000 00000000     0        0 4180 1 ce729580 300 0 0 2 -1                              
   5: 00000000:271A 00000000:0000 0A 00000000:00000000 00:00000000 00000000     0        0 4177 1 ce729140 300 0 0 2 -1                              
   6: 00000000:22BA 00000000:0000 0A 00000000:00000000 00:00000000 00000000     0        0 4176 1 ce728d00 300 0 0 2 -1                              
   7: 00000000:4E3E 00000000:0000 0A 00000000:00000000 00:00000000 00000000     0        0 5232 1 cabae900 300 0 0 2 -1                              
   8: 0200A8C0:271A 3200A8C0:DF40 08 00000000:00000001 00:00000000 00000000     0        0 22521 1 c4c5e580 21 3 6 3 -1                              
   9: 0200A8C0:271A 3200A8C0:DF24 08 00000000:00000001 00:00000000 00000000     0        0 22092 1 c4c5f680 21 3 4 3 -1                              
  10: 0100007F:22B8 0100007F:A7D2 01 00000000:00000000 02:000004FD 00000000     0        0 5304 2 c4c7fa40 20 3 1 5 -1                               
  11: 0200A8C0:271A 3200A8C0:DF4E 08 00000000:00000001 00:00000000 00000000     0        0 22670 1 c4c5e9c0 21 3 4 3 -1                              
  12: 0200A8C0:22B8 3200A8C0:A126 01 00000000:00000000 ?4
 assume that it not being listed as optional in the protocol, makes it mandatory?
d. The Drop Tamper message (C-bus reference 5.5.2.5) to the panel is not supported. (as above)
e. The Raise Alarm message (C-bus reference 5.5.2.6) to the panel is not supported.(as above)

2. I have seen a few incidences of the D16 (or MiniCentral as I?m not sure what handles what) refusing to accept keypad key press commands (C-Bus reference 5.5.2.7). Other aspects appear to still work and if I manipulate the panel through its own keypad I see outbound messages ok. The only way I have been able to fix the issue is to fully power cycle the panel (AC & battery).

3. The panel does not report zone status change messages when disarmed. Is there a reason for this as I notice the hardwired keypad shows this information accurately? The problem is a user cannot see the true state of all zones before arming the panel, or even after it is armed unless the zone subsequently changes state. The only way to solve this is to constantly poll the panel with Status 1 & 2 requests (C-Bus reference 5.5.2.1 & 5.5.2.1) and process the replies which do carry the correct status. This solution is very messy, and against all C-Bus rules of ?thou shall not poll?. It also carries a time penalty as it takes time for the request and reply to be processed by the panel leading to a delayed user experience when arming. What I am hoping you can do is just send the Zone status messages when the panel is disarmed also. I am aware however that there is possibly a concern about the amount of C-Bus traffic that may create, and I do understand that. But it is no worse than a C-Bus PIR being used as an occupancy sensor and reporting movement.

4. Can you tell me what the emulate keypad (C-Bus reference 5.5.2.7) inter key timeout value is? I have noticed if I am slow to type it seems to timeout and I do not get the desired operation (e.g. enter pin for disarm) It looks like the value is about 2 seconds, which is quite short when the messages are coming from a considerable distance, i.e. the message can be originated from an iPhone connected to the internet via 3g anywhere in the world, and >2 seconds between keystroke messages is quite possible.

5. Can you confirm the MiniCentral is also operational on the Ness M1? If this is the case I would like to test it, and promote it, as there are lots of sites that lie somewhere between a Concept or Challenger type system and a D16, that would fit perfectly into a panel like the M1.

----------------------------------------------------------------------------------
[B]NESS Reply[/B]

I have had some feedback from our Engineers as attached..

1a. The miniCentral does NOT support Zone Open and Zone Short. It does however support Zone Unsealed. The communication between the panel and miniCentral handles Zone Unsealed and Zone Sealed to identify the status of the zone.

1b. The MiniCentral does handle Zone Tampers. From what I can see it handles CBus tampers, Elk zone tampers and D8/D16 tampers.

1c. The MiniCentral sees the the CBus raise tamper but it is not being passed to the panels.

1d. The MiniCentral sees the the CBus drop tamper but it is not being passed to the panels.

1e. The MiniCentral sees the the CBus raise alarm but it is not being passed to the panels.

2. The panel expects a number string. While each button press is transmitted through the CBus system. Thus minCentral buffers the incoming CBus button presses and passes the mas strings. I haven't come across situations where the panel and miniCentral are out of synch with each other. WIll have to look into that....to see what is going on.

3. The miniCentral blocks but stores all the zone states during system being disarmed. We originally were passing the message onwards but were asked by Clipsal to block them. The reason behind it was that people are home so there would be alot of CBus traffic. I have looked through the documentation to see which note specifically states that....I couldn't find it. But I do remember we asked to remove it when CBus was approving our product.

4. See Point 2.

5. Yes miniCentral should work with the M1. It needs to set appropriately (ie. DIP switch) and port connections....see specs.

-------------------------------------------------------------------------
[B]My comments[/B]

It would appear that some functionality (such as the tampers) is supposed to be supported but for some reason is not. I never got to the bottom of these things as communication with NESS stopped.
I suspect the MiniCentral supports them, but there is some sort of interfacing issue between the MiniCentral and the panel, but I'm only guessing.

Rohan

 

Did you get this sorted out?