SENPILL (Multisensor) Occupancy sensor enabled after power failure

Discussion in 'C-Bus Toolkit and C-Gate Software' started by Charlie Crackle, Jul 16, 2006.

  1. Charlie Crackle

    Charlie Crackle

    Joined:
    Aug 3, 2004
    Messages:
    815
    Likes Received:
    8
    Location:
    Melbourne
    I have noticed the Multisensor has the occupancy sensor enabled after power failure even when set to disable in power failure tab.

    Firmware 1.9

    I have the SENPILL set as follows. Occupancy sensor disabled. Turn the power off and on an the occupancy sensor is enabled. Is this correct operation?

    Charles
     

    Attached Files:

    Charlie Crackle, Jul 16, 2006
    #1
  2. Charlie Crackle

    daniel C-Busser Moderator

    Joined:
    Jul 26, 2004
    Messages:
    766
    Likes Received:
    20
    Location:
    Adelaide
    Thanks Charlie.

    Smells like something worth digging into, I've reported it. (#9050)

    Daniel
     
    daniel, Jul 17, 2006
    #2
  3. Charlie Crackle

    Charlie Crackle

    Joined:
    Aug 3, 2004
    Messages:
    815
    Likes Received:
    8
    Location:
    Melbourne
    Is this a problem with version 2.0 firmware as well ?? or is this a toolkit issue and not firmware related

    I remember now I reported during the beta (quite a while ago....)

    using the search tool.... http://www.cbusforums.com/forums/showthread.php?t=443


    Charles
     
    Last edited by a moderator: Jul 17, 2006
    Charlie Crackle, Jul 17, 2006
    #3
  4. Charlie Crackle

    Charlie Crackle

    Joined:
    Aug 3, 2004
    Messages:
    815
    Likes Received:
    8
    Location:
    Melbourne
    From http://www.cbusforums.com/forums/showthread.php?t=443
    From http://www.cbusforums.com/forums/showthread.php?t=443

    Newman are you tallking firmware version 2.0 ? I thaught firmware version 2.0 was only released recently was it being worked on it back then.

    Is this a toolkit or firmware issue ??

    I had forgotten all about this bug till the other day when the power failed and I hand 4 Blue Night lights !



    Charles
     
    Last edited by a moderator: Jul 17, 2006
    Charlie Crackle, Jul 17, 2006
    #4
  5. Charlie Crackle

    daniel C-Busser Moderator

    Joined:
    Jul 26, 2004
    Messages:
    766
    Likes Received:
    20
    Location:
    Adelaide
    "V2" is the term used for CBusV2, the 16-bit commissioning software prior to Toolkit.
     
    daniel, Jul 18, 2006
    #5
  6. Charlie Crackle

    Charlie Crackle

    Joined:
    Aug 3, 2004
    Messages:
    815
    Likes Received:
    8
    Location:
    Melbourne
    So this is a toolkit / unit programming issue NOT a firmware issue.

    Charles
     
    Charlie Crackle, Jul 20, 2006
    #6
Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.
Similar Threads

  1. SENPILL After Power Failure....

  2. SENPILL Light Level and Occupancy.

  3. 06-019-1 Enable & Disable Status After A Power Failure

  4. Sunset Function on SENPILL and Light Level of 77 LUX goes 0 when Occupancy Enabled

  5. C-bus state recall from C-Touch after power failure

  6. PAC status after power failure

  7. L5504AMP not recover after power failure

  8. CBUS system after power failure

Loading...