cgate flow control

Discussion in 'C-Bus Toolkit and C-Gate Software' started by Dave Byron, Feb 28, 2005.

  1. Dave Byron

    Dave Byron

    Joined:
    Aug 3, 2004
    Messages:
    835
    Likes Received:
    0
    Location:
    Casurina
    Timing problem
    I have a test network on desk with a two 10cm cat5 cables from pc interface to dimmer to ctouch and burden.
    When i run toolkit 1.1.5 and one virtual ctouch and connect to test network then start scenes cgate reports errors.
    Now before you say its the network or hardware I can turn the errors off, select were they occur, and how often they occur.
    What i have had to do is put delays between scenes and play with the delay times till errors cease.
    My big question is this what will happen on real project.

    dave


    27/02/2005 12:36:44 PM C-Gate : Rx "[827] 200 OK: //grafton/254/56/5"
    27/02/2005 12:36:44 PM C-Gate : Rx "[828] 200 OK: //grafton/254/56/6"
    27/02/2005 12:36:44 PM C-Gate : Rx "[830] 408 Operation failed: //grafton/254/56/55"
    27/02/2005 12:36:44 PM C-Gate : Rx "# Command Failed: cmd="&[830]off 254/56/55" reason="Send failed (no confirm)" sessionId=cmd15 commandId=830"
    27/02/2005 12:36:44 PM C-Gate : Rx "# Command Failed: cmd="&[831]off 254/56/1" reason="Send failed (no confirm)" sessionId=cmd15 commandId=831"
    27/02/2005 12:36:44 PM C-Gate : Rx "# Command Failed: cmd="&[832]off 254/56/23" reason="Send failed (no confirm)" sessionId=cmd15 commandId=832"
    27/02/2005 12:36:44 PM C-Gate : Rx "[831] 408 Operation failed: //grafton/254/56/1"
    27/02/2005 12:36:44 PM C-Gate : Rx "[832] 408 Operation failed: //grafton/254/56/23"
    27/02/2005 12:36:44 PM C-Gate : Rx "# Command Failed: cmd="&[833]off 254/56/4" reason="Send failed (no confirm)" sessionId=cmd15 commandId=833"
    27/02/2005 12:36:44 PM C-Gate : Rx "[833] 408 Operation failed: //grafton/254/56/4"
    27/02/2005 12:36:44 PM C-Gate : Rx "# Command Failed: cmd="&[834]off 254/56/5" reason="Send failed (no confirm)" sessionId=cmd15 commandId=834"
    27/02/2005 12:36:44 PM C-Gate : Rx "# Command Failed: cmd="&[848]off 254/56/50" reason="Send failed (no confirm)" sessionId=cmd15 commandId=848"
    27/02/2005 12:36:44 PM C-Gate : Rx "# Command Failed: cmd="&[849]off 254/56/82" reason="Send failed (no confirm)" sessionId=cmd15 commandId=849"
    27/02/2005 12:36:44 PM C-Gate : Rx "# Command Failed: cmd="&[850]off 254/56/54" reason="Send failed (no confirm)" sessionId=cmd15 commandId=850"
    27/02/2005 12:36:44 PM C-Gate : Rx "# Command Failed: cmd="&[851]off 254/56/55" reason="Send failed (no confirm)" sessionId=cmd15 commandId=851"
    27/02/2005 12:36:44 PM C-Gate : Rx "# Command Failed: cmd="&[852]off 254/56/53" reason="Send failed (no confirm)" sessionId=cmd15 commandId=852"
    27/02/2005 12:36:44 PM C-Gate : Rx "[834] 408 Operation failed: //grafton/254/56/5"
    27/02/2005 12:36:44 PM C-Gate : Rx "[836] 200 OK: //grafton/254/56/82"
    27/02/2005 12:36:44 PM C-Gate : Rx "[837] 200 OK: //grafton/254/56/54"
    27/02/2005 12:36:44 PM C-Gate : Rx "[838] 200 OK: //grafton/254/56/55"
     
    Dave Byron, Feb 28, 2005
    #1
Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.
Similar Threads

  1. New Software with Cgate

  2. CGate cannot find application

  3. Cgate Question from Novice

  4. 06-052-1 Homesafe Dialler Configuration Flow Chart

  5. Use cgate control cbus by time

  6. 24v DC Blind control using shutter control

  7. How to read Enable-Control group level via CGate?

  8. Measuring water flow (or pressure or both?) from dam pump

Loading...