Wiser works with multi network

I try to install wiser in my topology network, there are 6 different network which connect to six 5500 nb, star topology, and wiser is backbone / master hook. ( centre of star topology network)

Unfortunately, piced read wrong message when i try to transfer to wiser or trial running by software, the message is " network usage is 254"

What is the meaning?

Anybody maybe can give advise to related issued?

Thank in advanced

Vincent

 

I'm having difficulty understanding your setup. Wiser can be setup in many different ways. I highly recommend listing the network information for the devices involved. If possible, adding wireshark capture helps a lot. You can see previous posts for examples of this. Here are a few parameters you may wish to list:
- are you able to ping the Wiser from the PC
- IP address/netmask/gateway of the PC that you are running PICED on
- is the Wiser used as a router (ie: PC is on Wiser's LAN) or is the Wiser used as a LAN device (ie: PC is a peer on the same LAN as the Wiser) or is the Wiser accessed from WAN (ie: PC is on the same LAN as the Wiser's WAN port)
- LAN IP address/netmask of the Wiser
- LAN IP address/netmask entered into the PICED project on the Wiser
- is remote project control/toolkit control/project update enabled in the project
- are you able to connect to the Wiser's web server and what is reported by the Adobe Flash user interface for these settings

 

Wiser multi network

Hi..
Thanks for your reply..
I mean are :
1. There 6 network in cbus topology
2. I connect wiser in back bone cbus topology, so 6 cbus network will be conect to wiser.
3. So far if wiser goes normally if i'm not connect to c bus network.
4. Is it posibble , if i conect 6 cbus network with inline cni (from wiser) or i have to put din rail CNI ?

Another question, howto make multipage or sub pages in wiser, i mean i have so many channel have to show in komputer / ipad , or other device , such page 1b, 1c, 1d, 1e .....


Thank in advanced

Rgds
Vincent

 

That error message does not sound correct. Can you provide the error number and the exact text?

 

The 6 networks are not able to be connected to Wiser. I assume you mean that they are to be connected to the backbone network.

The six networks should each be connected to the backbone network using C-Bus bridges. They can not use the Wiser CNI. If you use CNIs on the 6 networks, you will need some means of routing messages between the networks (like Schedule Plus or HomeGate). Wiser can not send messages to C-Bus networks via CNIs.

I would suggest that you read this document about C-Bus Networks

You can add as many pages as you like using locations or function groups. Sub-pages are not possible in Wiser.

 

hi Guys

thank for your advice ,
i give you my FR :

i already put 6 NB in my network topology .... it work good
and put wiser in front of them with inline CNI.. so far it works well also..

another question .... if i want to add OPC or sch plus, do i have to add din rail CNI or , i can use inline CNI ( from wiser)

what about working with BMS ( Buiding management system , just like software from mitsubishi PLC), please advice

thank in advance

best regards
Vincent

 

Only one device can use a CNI at a time. If you connect to the Wiser's CNI, then Wiser will stop operating until the CNI has been released again.

 

Hi Darren

Ok thank Dareen....

Anyway about work together with mitsubishi PLC software...

Can you give me advise about software ?

Another question ... What about scheedule plus . . . Can scheed plus do like web interface . . . Or work in flash ?


Thank in advanced


Best regards
Vincent

 

If you want to know about the capabilities of Mitsubishi software, you should check with them.

Schedule Plus can give a web interface via the ServerX software.

 

Hi Darren

Thank for your advise..
I will check for mitsubishi plc software platform.

Another issue about schedule plus works with server X, could you tell me what kind of server X, is it in clipsal software download center ?

Should the server X works with schedule plus dongle?

Thanks and regards,
-vincent-