Problem with Cbus not responding immediately

[loesch]

I bought home with HomeGate 3.4.1.0 CGate 2.5.23 build 2123,

The computor does not respond when I click the icons on the screen ,the functions then only come on after I clicked on the time of the computor at the bottom right and ok .
What can be the cause ,and can I download a newer better version , everything was working fine but computor was not responding and had to be switched of ,problem started after this problem .It show 0/1 networks online and only change for a short time to 1/1 network online if I click on the time or go to operation mode .I tried to reinstall HomeGate 3.4.1.0 but it gives the following error 1,setup has failed to find a valid install of homegate
please help urgently

[Newman]

It sounds like the PC might have a few issues going on there, so the best place to start is with a phone call to Clipsal Technical Support.

http://www2.clipsal.com/cis/technical/technical_support

Some useful information to gather before you call will be things like:

• Tech specs of the PC it's installed on
• Whether you are using a touchscreen or a mouse for input
• Operating system the PC is running on
• Whether the HomeGate dongle is plugged into the PC (without the dongle, HomeGate will not operate correctly as it tells HomeGate that it is a legal copy of HomeGate)

[Darren]

Originally Posted by loesch

The computor does not respond when I click the icons on the screen ,the functions then only come on after I clicked on the time of the computor at the bottom right and ok .
What can be the cause ,and can I download a newer better version , everything was working fine but computor was not responding and had to be switched of ,problem started after this problem .It show 0/1 networks online and only change for a short time to 1/1 network online if I click on the time or go to operation mode .

If it shows 0/1 networks on-line, then there are communications problems. HomeGate can not control C-Bus if the networks are off-line. You need to solve this problem before doing anything else. Refer to the document C:\Clipsal\HomeGate\Manuals\Advanced Fault Diagnosis.pdf for details of analysing site problems.

Originally Posted by loesch

I tried to reinstall HomeGate 3.4.1.0 but it gives the following error 1,setup has failed to find a valid install of homegate
please help urgently

Do you have the CD with HomeGate on it?

If not, it is possible that your version of HomeGate is not licensed.

From a valid version 3.4.1 of HomeGate, you should be able to upgrade to V3.9.0 to get a more up to date version. This can be obtained by going to http://www2.clipsal.com/cis/technica...oads/home_gate and clicking on the Show Old Versions link. To go past this version, you will need to purchase a dongle.

[loesch]

Thank you for the help I downloaded the homegate 3.9 and cbus toolkit 6.1 ,and it works fine now on start up for 5 minutes it showns 1/1 network online ,and after 10minutes 0/1 network online .
In the jave screen it shows: Hardware key initialize failed(driver not installed)
license file found: customer name ublic,locationublic , license typeublic,network license:2, expiry: 31 december 2099 and then
20100311-133524 827 //d_cook/254 4f22b760-6e3a-1028-92cb-e9897d67db5b c-bus send error: (%) (retrying)
checking license

please help

[Darren]

Prior to V4 of HomeGate, it was C-Gate that had to be licensed. Since V4, it is HomeGate that needs the license.

So for V3.9 of HomeGate, you will need to have a C-Gate dongle. If you don't have one, C-Gate will time-out.

[loesch]

Thank you ,I have a clipsal pc interface RS232 connected to the serial port.Which version do I need to install just to get everything working,because everything was working fine before the power out.After I installed the newer versions the one black and white keypad started rebooting every minute.I had the homegate 3.4.1 originally installed ,which cgate and cbus toolkit need I install to get everything just to work.pleaseeeeee

Regards
Loesch

[Newman]

The C-Bus software downloads pages show a compatibility chart to show which versions of the various pieces of software work with each other.
http://www2.clipsal.com/cis/technica...oads/home_gate

If possible, I would try and persevere with HomeGate 3.9.0. It will enable you to use newer versions of the other C-Bus software products, which might not be so important now, but could become an issue if you decide to expand on your installation with products that weren't available at the time those old software versions were created.

You say:

one black and white keypad started rebooting every minute

... can you give some more information? Is this a C-Bus product? How is it related to your HomeGate installation?

[Darren]

Originally Posted by loesch

Which version do I need to install just to get everything working,because everything was working fine before the power out.After I installed the newer versions the one black and white keypad started rebooting every minute.I had the homegate 3.4.1 originally installed ,which cgate and cbus toolkit need I install to get everything just to work.pleaseeeeee

You haven't said whether there is a dongle plugged into your PC. This determines what is possible.

[loesch]

Thank you ,I have a clipsal pc interface RS232 connected to the serial port,is that what you are talking about.

which version should I download of homegate and cbus in the meantime ,and where can I get a dongle and will it sort out all the problems.

regards
Loesch

[Newman]

The Clipsal PC Interface is not the dongle, it is just the interface between the PC and the C-Bus network.

A C-Gate dongle is a parallel port adapter that plugs into the parallel port of your PC. When you buy HomeGate (it is not free) the licence is supplied on this parallel port adapter, called a dongle.

If you have bought this house recently, but the owner has not left you the parallel port dongle on the PC running HomeGate, then he has effectively taken your permission to use HomeGate with him.